1. Laminations of core are generally made of
(a) case iron
(b) carbon
(c) silicon steel
(d) stainless steel
(a) 0.005 mm
(b) 0.05 mm
(c) 0.5 m
(d) 5 m
(a) reduce the bulk
(b) provide the bulk
(c) insulate the core
(d) reduce eddy current loss
(a) length of conductor
(b) cross-sectional area of the conductor
(c) number of conductors
(d) all of the above
(a) mica
(b) copper
(c) cast iron
(d) carbon
(a) copper lugs
(b) resistance wires
(c) insulation pads
(d) brazing
(a) copper is harder than mica
(b) mica and copper are equally hard
(c) mica is harder than copper
(d) none of the above
(a) rivets
(b) counter sunk screws
(c) brazing
(d) welding
(a) motion of conductor
(b) lines of force
(c) either of the above
(d) none of the above
(a) magnetic flux, direction of current flow and resultant force
(b) magnetic flux, direction of motion and the direction of e.m.f. induced
(c) magnetic field strength, induced voltage and current
(d) magnetic flux, direction of force and direction of motion of conductor
(a) case iron
(b) carbon
(c) silicon steel
(d) stainless steel
Ans: c
2. Which of the following could be lamina-proximately the thickness of lamina-tions of a D.C. machine ?(a) 0.005 mm
(b) 0.05 mm
(c) 0.5 m
(d) 5 m
Ans: c
3. The armature of D.C. generator is laminated to(a) reduce the bulk
(b) provide the bulk
(c) insulate the core
(d) reduce eddy current loss
Ans: d
4. The resistance of armature winding depends on(a) length of conductor
(b) cross-sectional area of the conductor
(c) number of conductors
(d) all of the above
Ans: d
5. The field coils of D.C. generator are usually made of(a) mica
(b) copper
(c) cast iron
(d) carbon
Ans: b
6. The commutator segments are connected to the armature conductors by means of(a) copper lugs
(b) resistance wires
(c) insulation pads
(d) brazing
Ans: a
7. In a commutator(a) copper is harder than mica
(b) mica and copper are equally hard
(c) mica is harder than copper
(d) none of the above
Ans: c
8. In D.C. generators the pole shoes are fastened to the pole core by(a) rivets
(b) counter sunk screws
(c) brazing
(d) welding
Ans: b
9. According to Fleming's right-hand rule for finding the direction of induced e.m.f., when middle finger points in the direction of induced e.m.f., forefinger will point in the direction of(a) motion of conductor
(b) lines of force
(c) either of the above
(d) none of the above
Ans: b
10. Fleming's right-hand rule regarding direction of induced e.m.f., correlates(a) magnetic flux, direction of current flow and resultant force
(b) magnetic flux, direction of motion and the direction of e.m.f. induced
(c) magnetic field strength, induced voltage and current
(d) magnetic flux, direction of force and direction of motion of conductor
18 comments:
very much helpful
Good question for examination *b
very helpful..
Ma Sha ALLAH boht achy swal hn
subhan allah
Excellent Post About Emergency MELTDOWN Generators Shutdown and Dc generator parts.
Thanks
Thanks
Thanks again....................
wow
very useful
thank u so much..
can v copy it..?
thnks again sir......
Que no 44 Ans B
Que no 44 Ans B
Que 70 And D
Que 71 Ans C and D
thank u so much
Post a Comment